Gun lockers or safes are specifically designed for the secure storage of guns and ammunition. They broadly resemble normal single-tier lockers, but tend to be slightly less high than normal single-tier lockers, and are often free-standing, and not banked together. They are fitted with internal racks designed for holding firearms. They have a shelf at the top like normal single-tier lockers, although in this case it is closed and locked by a separate door, because of legal requirements in some countries that firearms and ammunition be stored and locked separately. They always lock with three-point locking, which is in some countries a legal requirement for the storage of firearms. Sometimes they are made of the standard kind of sheet steel used in manufacturing normal lockers, and sometimes they are made of extremely thick heavy-duty steel and in this case resemble a safe more than a normal locker. In Australia there are strict regulations governing the storage of firearms following the Port Arthur massacre in Tasmania, Australia on 28 April 1996, and cabinets used for storing firearms must be bolted to the floor or a wall if the cabinet is under a certain weight. Dedicated gun lockers are likely to include holes in the cabinet to accommodate such bolting. Several locker manufacturers also offer dedicated gun lockers. Locker Colorado
Material: steel is the traditional material; but wood, plastic, or laminate are sometimes used. Plastic or laminate lockers are sometimes advocated in environments, such as near swimming pools, where moisture accumulation may cause steel lockers to rust over time. They can also be used in external applications where internal space is not available. Locker
Number of locking points: Locker doors may lock with either single- or three-point locking, but this is not normally chosen as a separate option, and the choice is usually dependent on the number of tiers in the lockers, or whether they are a high-security model, although some manufacturers do allow purchasers to specifically choose an option here that goes against their normal practice. Single-point locking locks the door at only the point where the latch engages with the door-frame, whereas three-point locking uses extensible steel rods to lock the top and bottom of the door as well. Locker CO
If you’d like to make your new security system matching your cabinets, we can help you with décor ideas. Our products come in a wide variety of materials, colors and finishes. Our antique-styled cabinet locks will go perfectly in older, wooden furniture, and stainless-steel locks are ideal for steel filing cabinets. We even have store-quality locks for clear sliding-glass display cases. Locker CO
Unlike our competitors, we make it a point to refurbish all of our used lockers so that we can deliver a quality product for the cheaper price you want. With warehouses on the East and West coasts, we're able to store several lockers so that we can bring you the best selection possible. Find the shape, color, and size that works best for you with just a few clicks. Our site is simple to navigate, easing the process of buying so that you can spend more time on the things that matter to you. Need help? We're just a call or an email away and we're always happy to assist you at any stage of your buying process. Locker Colorado

Number of locking points: Locker doors may lock with either single- or three-point locking, but this is not normally chosen as a separate option, and the choice is usually dependent on the number of tiers in the lockers, or whether they are a high-security model, although some manufacturers do allow purchasers to specifically choose an option here that goes against their normal practice. Single-point locking locks the door at only the point where the latch engages with the door-frame, whereas three-point locking uses extensible steel rods to lock the top and bottom of the door as well.

Stepped/2-step lockers are two-tier lockers, usually available only in 15-inch (38-cm.) width; but the compartments and their doors have an L-shaped cross-section, which causes the division between the doors to follow a zigzag pattern. This configuration enables more hanging height to be included in both upper and lower lockers; but part of each compartment (the lower part of the upper one and the upper part of the lower one) will be only half the usual width of two-tier lockers.
Dimensions (Note that, in English-speaking countries, even those commonly using metric measurements now, locker dimensions are usually clean numbers of inches or feet, while the corresponding metric measurements are uneven, involving decimal places when precision is required, presumably resulting from continued use of locker designs based on feet and inches, unchanged for decades other than for cosmetic features.): Locker
Lockers are usually physically joined together side by side in banks, and are commonly made from steel, although wood, laminate, and plastic are other materials sometimes found. Steel lockers which are banked together share side walls, and are constructed by starting with a complete locker; further lockers may then be adding by constructing the floor, roof, rear wall, door, and just one extra side wall, the existing side wall of the previous locker serving as the other side wall of the new one. The walls, floors, and roof of lockers may be either riveted together (the more traditional method) or, more recently, welded together.
Division 10 — Specialties Lockers: Division 10 — Specialties is a category within the National Master Specification (NMS) set of guidelines developed by Public Works and Government Services Canada. Division 10 — Specialties items that could be required within a locker room (to meet commercial building and construction regulations) are lockers, washroom accessories, toilet compartments, and toilet partitions. Lockers are constructed of two sides: a back, top and a bottom. Different types of materials are used in locker manufacturing, offering a wide variety of metal lockers, stainless steel lockers, solid plastic lockers, solid phenolic lockers, and custom lockers. A padlock is the most common way to lock a locker; however, you can also use a keyed cylinder lock, built in combination locks or keypad locks. There are a lot of optional extras that can be utilized for lockers, for example: bases, sloping tops, end panels, customized shelves and hooks as well as the locking method (coin-operated lockers are another option). The environment is the best way to distinguish what type of locker will be required for which type of space. For example, if you are putting gym lockers into a humid area, or anywhere close to showers, stainless steel or solid plastic lockers would be most suitable because they are moisture-resistant and rust-resistant. Wood lockers would not be appropriate for this type of environment because the moisture from the humidity would rot the wood. School Locker
Unlike our competitors, we make it a point to refurbish all of our used lockers so that we can deliver a quality product for the cheaper price you want. With warehouses on the East and West coasts, we're able to store several lockers so that we can bring you the best selection possible. Find the shape, color, and size that works best for you with just a few clicks. Our site is simple to navigate, easing the process of buying so that you can spend more time on the things that matter to you. Need help? We're just a call or an email away and we're always happy to assist you at any stage of your buying process. Locker
×